Used Carburetors Questions:

Question #1:

wiring an inline electric fuel pump?

I had a Fuel Injected render pump installed and employed in my 86 GMC though the locomote is a 92 Chevy 350. I have denaturized to a carburetor & a 7 lb electric fuel pump. The older viscus works with a accommodate coming discover of the wiring command on the fire wall, but it has too much pressure, so I got a newborn digit but I had to take it all apart after it was installed because it wont work unless I dont ingest the ignition and enter directly to the battery.The accommodate registers same the shelling & I grounded the embody better to make trusty it isnt the ground,,heck I grounded it on the brake booster, core support, alt, shelling and the inclose rail,,nothing using the hot wires coming discover of the loom. WTF
Its a 86 GMC that had a carberator & the 305 had the machinelike pump,,I denaturized it to a 92 FI 350,,,worked fine for some eld but I hit absent to a Carburetor so I bought a 4-7 lb electric render pump, Dont poverty a toggle switch,,,really

Question #2:

Truck idling problems?

Hey guys, I've got an 86 Mitsubishi Mighty Max Pickup v4 2.0 2wd.

After I take it on the freeway and intend it warmed up pretty blistering or meet drive on the street for most 10 miles, my pushcart starts to idle roughly and it acts as if it's most to die. So I hit to put it in neutral at flushed lights and press the pedal to keep it from dying.

I proven using carburetor preparation and it worked for a week but then the problem happened again.

What could it be and how crapper I fix it?

Question #3:

What is the speed for dirt bike?

What is the speed for soil bike?

What is the pace bike with Honda gx 160 engine using Wheel rear\ face Diameter 20 progress and Teeth On Axle 32 and Teeth On Clutch 12 , What is the speed on the agency straight and Can the uprise up hill road ?

Specifications Engine :

Engine Type : Air-cooled 4-stroke OHV
Bore x Stroke : 68 X 45 mm
Displacement : 163 cm3
Net Power Output : 4.8 HP 3.6 kW @ 3,600 rpm
Net Torque ; 7.6 lb-ft 10.3 Nm @ 2,500 rpm
PTO Shaft Rotation : Counterclockwise from device dig lateral
Compression Ratio : 9.0 : 1
Lamp/Charge coil options : 25W, 50W / 1A, 3A, 7A
Carburetor : Butterfly
Ignition System : Transistorized generator
Starting System : Recoil Starter
Lubrication System : Splash
Governor System : Centrifugal Mechanical
Air cleaner : Dual Element
Oil Capacity : 0.61 US qt. 0.58 L
Fuel Tank Capacity : 3.3 U.S. qts 3.1 liters
Fuel : Unleaded 86 octane or higher
Dry Weight : 33 lbs. 15.1 kg

thanks

Question #4:

what carburetor to use on a vw beetle a dual 34 ict weber or a 32/36 progressive weber?

Hi all i hit a 1971 1600 twin port vw beetle with a have solex 34 pict 3 carb which is dead but what should i change it with and can anybody gratify verify me the pros and cons of apiece of the mass carb ordered ups. Should I follow with the solex if so why or should I go for a set of dual weber 34 ict carbs if so why or should i go with a proportional 32/36 weber thanks for your help

Question #5:

Homelite 955V1 2-Stroke Engine Running Problem?

Hi, I fresh acquired an old Homelite 955V1 2-Stroke 2 wheel saw which does not countenance like it has been used rattling much..
It had been unused for many years.
When I got it off the previous someone it was streaming OK.
I used it continuesly for approx 5 hours with no problems.
I then mitt it for 2 weeks and when I started it it obstructed after most 20 seconds, and then would not run again.
I took the carburettor apart and clean it discover and the diaphram etc every looked OK.
I replaced the fuel lines with new.
There is a beatific flash but it ease module not run.
If I vanish the flash plug and place some petrol in it will run for a some seconds but then stops.
When starting it this way the render distinction filled up with petrol.
If the crankshaht oil seals needed replacing would it still move by swing petrol in the block mess ?
I hit lowercase undergo of 2-strke engines so any ideas what could be wrong would be such appreciated.
Thanks,
Gary

Used Carburetors

Question #6:

Craftsman snow blower will not run?

i own a Craftsman 22 in. Snow Thrower with a 5 HP Two Stage Tecumseh Engine Model:247.887000. i recently tried to ingest it and had problems play it. erst started i was not able to movement more than a foot into the snow when it stalled and has continuing to dillydally out. i hit denaturized the sparkplug, which did not hit much copy on it and changed the gas. it ease will not run. some suggestions? carburetor problems?

Question #7:

1985 Suzuki LT 90 Quadrunner won't start?

So i traded my old Phantom Racing Banshee for a four wheeler because I'm using it to build an off-road kart but that's added story...
Today when i got the four wheeler the vender did inform me it didn't separate it necessary a lot of work likewise but i desired a project so i traded him so when i got home i took the carburetor unconnected clean it with carb. preparation place newborn pedal in and it wouldn't modify turn over so i checked for spark and it was perfectly fine...What else should I try?

Question #8:

should i go for engine decarbonisation?

hi there
i possess a maruti 800 carburetor 200 model...which has done nearly 45000kms on the odo
im rattling effort worried most the mileage of my car
i intend around 12kmpl in municipality and nearly 16kmpl on route without a/c..
fresh i hit done a top-up of engine oil..
please verify me if i have to do decarbonisation....my dad used to intend this car ,now he drives the new automobile ..he says its nt necessary to do that decarbonisation ..he says its just the worn discover clutch and my driving style..
gratify provide me your suggestion ....
is it sufficiency to intend the carburetor clean ..

Question #9:

engine problems While driving?

I hit the 1986 Plymouth colt 1.5 single disbursement cam, I have been having problems with the engine selection discover at various nowadays of driving, mainly going uphill And occasionally on a straightways. . I hit replaced clean lines, restored the carburetor, replaced fuel filters, and change the render pump that his engine mounted with an Electric Gas pump.

Compression push the starter motor running, enrich flooded open, coil HT leads disconnected 149 LB F/IN squared 10.48 TGF/CM squared Maximum variation between cylinders 15 LBF/ in squared 1.05 TGF/CM squared .

When I ingest a pressure gauge expanse what should I be hunting for in an senior vehicle like this, or some other suggestions would be very helpful

Buy Auto Parts for Less