Torque Specifications Questions:

Question #1:

How to choose an electro-motor?

For a project I hit to superior a suitable motor from mavilor.es

I have not been told wether I should ingest a DC or AC motor, however the force I am trying to accomplish is not avaialble in their DC motors so I hit gone to AC.

I am potty on where to start. My specification requires a circumscribed pace 10mm/s and I have worked discover a required force around 20 Nm for the motor.

When choosing the motor I have options of Stall Torque and Peak Torque, what should I be hunting for? Also a torque/speed graph, is it assumed that the locomote module hit whatever sort of speed control?

Question #2:

What is the speed for dirt bike?

What is the speed for dirt bike?

What is the pace bike with Honda gx 160 engine using Wheel rear\ face Diameter 20 progress and Teeth On Axle 32 and Teeth On Clutch 12 , What is the speed on the road straightforward and Can the rise up construction agency ?

Specifications Engine :

Engine Type : Air-cooled 4-stroke OHV
Bore x Stroke : 68 X 45 mm
Displacement : 163 cm3
Net Power Output : 4.8 HP 3.6 kW @ 3,600 rate
Net Torque ; 7.6 lb-ft 10.3 Nm @ 2,500 rpm
PTO Shaft Rotation : Counterclockwise from device dig side
Compression Ratio : 9.0 : 1
Lamp/Charge coil options : 25W, 50W / 1A, 3A, 7A
Carburetor : Butterfly
Ignition System : Transistorized magneto
Starting System : Recoil Starter
Lubrication System : Splash
Governor System : Centrifugal Mechanical
Air cleaner : Dual Element
Oil Capacity : 0.61 US qt. 0.58 L
Fuel Tank Capacity : 3.3 U.S. qts 3.1 liters
Fuel : Unleaded 86 octane or higher
Dry Weight : 33 lbs. 15.1 kg

thanks

Question #3:

What type of motor is required?

I'm hunting for a pancake/flat motor so that it shouldn't have a length more than an progress that is confident of touch 30,000 RPM low a load. The load would be a disc with a accumulation of 55 grams, a length of 1 inch, and a thickness of 1/4 inches. The round should be able to achieve 30K RPM in about 10 seconds or less. What specifications would the motor requirement to have? Like torque? Am I forgetting anything else?

Also, I came across digit assorted motors in my search. Would these do the job?

MicroMo:




nuvoDisc:


Thanks!

Question #4:

Does Hayne manual have torque specifications for motor mounts, transmission mounts?

I specifically want to acquire a Haynes manual for the force specifications of motor and tranny mounts, but i undergo i will find it useful later on. I am hunting to get the manual for 94-04 mustang.

Question #5:

Lincoln LS 3.8 Liter Vs. Chrysler 300 HEMI,.. WTF?!?

Alright, if i'm being Naive here someone please tell me.. But i was looking on Vehix and it says that a 2002 Lincoln LS 3.8 Liter V8 has a higher Net Torque and Horsepower than a 5.7 Liter V8 Chrysler 300 with freaking HEMI, I can't conceive this. However it did say that new there prices were about the same but ease i have a hornlike instance believing this, someone tell me if i'm datum this wrong.

Question #6:

Auto repair manuals? 2003 chevy silverado 4 by 4 5.3 liter engine torque specifications?

Torque specifications

Question #7:

How do I calculate the gear ratio I will need?

I am using a motor with these specifications:
Voltage range - 10-13 volts
RPM with no load speed - 5220
RPM with rated alluviation speed - 4120
rated alluviation - 30 g/cm

I will be using 2 of these motors to drive a 3 pound vehicle up a 40 honor disposed plain for 8 inches with cell treads. How do I calculate the equipment ratio that will provide enough torque for this task? I undergo this is belike a complicated problem, but if someone crapper just point me in the correct direction or intend me started that would be awesome! Thanks!I

Question #8:

The tune-up specifications of a car call for the sparks plugs to be tightened to a torque of 31 N m. You plan?

The tune-up specifications of a car call for the sparks plugs to be tightened to a force of 31 N m. You plan to alter the plugs by pulling on the end of a 50 cm long wrench. Because of the cramped expanse under the hood, you'll need to pull at an seek of 137° with attitude to the shaft. With what force in N must you pull?
this is physics.

Question #9:

Please help, need to produce an engine specification, but cant work it out?

I need to display an engine spec for a automobile that can get up to 150mph and display noesis as a function of force kinda than high rpm. The engine`s stroke / bore ratio staleness be at least 4:5 So attack length separated by bore diameter equals at least 0.8 . Engine swept volume should not top 2 litres, and be an in-line 4 cylinder configuration and have maximum stingy piston speed of 22m/s. The container crowning speed is based on a drag coefficient of 0.6 and a container frontal Atlantic of 1.8m2.
In the specification I have to include:
• Bore and Stroke dimensions Decided on Stroke of 90cm and Bore 80cm
• Compression ratio
• Projected outputs for Brake Horse Power, Indicated Power, Torque, BMEP
• Frictional Losses

Please support me, Can any tell me how I work it all out???
The car needs to do 150mph, and have worked discover that to accomplish 150mph module order 270bhp.

Question #10:

PHYSICS QUESTIONS!!!?

The tune-up specifications of a automobile call for the spark plugs to be tightened to a torque of 48 . You plan to tighten the plugs by pulling on the end of a 26-cm-long wrench. Because of the cramped expanse under the hood, you'll need to pull at an seek of 105 with respect to the wrench shaft.

With what force must you pull?
48 Nm and 105 degrees. Sorry & impart you!



** Powered by Yahoo Answers