Homelite Questions:

Question #1:

Homelite VI-955 Chainsaw Service Manual Wanted?

Does anyone have or know a place where I crapper download for liberated a :- Homelite VI-955 Chainsaw Service Manual ?
I already have the parts drill but need the Service manual.
I have been told that there is a HOMELITE XL700 THRU VI-955 SERVICE MANUAL.
That or one that only covers the 955 V1 is what I need.
Thanks
I hit approx 1 period past been on the …and also House of Homelite websites and asked for a unification to the download as have some other grouping but apparently no digit has had a reply from the person who offered them.

Question #2:

Homelite 955V1 2-Stroke Engine Running Problem?

Hi, I recently acquired an old Homelite 955V1 2-Stroke 2 wheel chainsaw which does not countenance same it has been utilised rattling much..
It had been unused for many years.
When I got it off the previous someone it was streaming OK.
I used it continuesly for approx 5 hours with no problems.
I then mitt it for 2 weeks and when I started it it obstructed after about 20 seconds, and then would not run again.
I took the carburettor apart and clean it discover and the diaphram etc every looked OK.
I replaced the render lines with new.
There is a beatific flash but it still module not run.
If I vanish the spark block and put whatever petrol in it module separate for a few seconds but then stops.
When starting it this way the fuel line filled up with petrol.
If the crankshaht oil seals needed replacing would it ease move by putting petrol in the plug mess ?
I have lowercase undergo of 2-strke engines so some ideas what could be criminal would be much appreciated.
Thanks,
Gary

Question #3:

How much is my antique Homelite saw worth ?

I hit a running and fully useful Homelite wiz 55 old gear drive chainsaw- It has 1/2 movement x 63 breadth huge concern that is nearly impracticable to find. It is a great saw with tons of power and I love streaming it, it sounds same a motorcycle, and it has a brute forbid -

Rather than spend on added chain or a custom 404 transmutation maybe I should sell it to a collector?

What's it worth about?

Question #4:

How are chainsaw pitch and bar size / type related? What is chain gauge? 7-tooth vs 8-tooth?

I have two example Homelite EZ's from 1957/1958; not the newer models that I'm currently employed on. They were 40 and they were only absent their official covers, so I figured it was a good deal. Well, I didn't investigate the saws, then I come to find discover they separate 7/16" pitch sprockets. I also found discover that 7/16" pitch chain isn't oversubscribed anymore. Alright, recreation so far.

One saw had the example 7/16" movement sprocket, chain, and bar; the another had exclusive the 7/16" sprocket. So, I sequential and installed an Oregon PowerMate .404 pitch 7-tooth rim sprocket. This is where I requirement whatever help.

I have no forbid and no chain for the .404 saw. I don't have such undergo with chainsaws, so these are questions I would same to know about:

Can any size chain pitch be utilised on some forbid as daylong as the length of the concern is equal to forbid length? e.g. can 3/8" pitch concern and .404 pitch chain be separate off the same bar if they're the same length?

The 7-tooth tooth is also advertised in an 8-tooth sprocket. Does the difference in set on the sprocket attain a difference on the saw, the concern I can use, the bar, or all of the above? Do I have to be selective in the concern that I buy?

Can bars from assorted saws be utilised on a Homelite - especially an older model - or module this create issues with the oiler?

Because whatever exerciser hit rollers and others are hardnose, does this make a difference when streaming a concern on it?

Is there ease somewhere that sells 7/16" movement chain, and if so, where?

And the terminal abstract I don't know: what is concern gauge .050, .058, .063, etc and does it effect what type / size of bar I can use?

Thanks for some and all help - it's very much appreciated.

Question #5:

Which Homelite Chainsaw pull starter is compatable with the John Deere J3816?

The vantage starter nuimber is 07873

Question #6:

Where can I get an online owners manual for an 18 inch Homelite d3850b chainsaw?

Homelite d3850b
18 progress bar
38cc disposition

Question #7:

I have an old John Deere chainsaw. It is an J 3816. The pull starter is shot. Did Homelite build my chainsaw?

I need to undergo where I can intend a equal pull chain starter and will a Homelite work? The model of the vantage official is UP07873.

Question #8:

Chainsaw carb question?

Chainsaw carb question?
i got a homelite 45cc chainsaw and the carb is beyond bushel and they dont make parts for the saw anymore. it has a carb kindred to this if not just the same. i undergo it module sound the engine and everything but will it power the 45cc engine? Btw i am feat to increase it on a lowercase cycle i have and use the bikes sending to go faster.

Question #9:

chainsaw 2 stroke oil ratio?

Hi, I have a Homelite V1-955 chainsaw. In the specifications it says the Fuel lubricator Ratio is 32:1. Is this still the precise ratio when using a recent oil. The oil I am using is Carlube 2-Stroke Garden Machinery Oil, APITC Specification.

Question #10:

I have an old homelite super 2 chain saw?

The chord broke so I relaced it and the concern My problem is I definite to fool around with the carburator settings ,it was running ok before . Now pedal comes out of the muffler and it won't start. I proven environment it according to the drill ,anybody got some advice? Thanks
Renpen, can I unscrew the needle every the way ,remove it spray carb preparation in there and put it right back ,or will something fall unconnected if I verify it discover ? Thanks



** Powered by Yahoo Answers